Technical Articles

metalworkingmag.com
KEBA News

EXTEND THE MOLD LIFESPAN AND SPEED UP THE MOLD EXCHANGE PROCESS

KEBA concepts and KePlast Smart Functions enable faster and more accurate control technology.

EXTEND THE MOLD LIFESPAN AND SPEED UP THE MOLD EXCHANGE PROCESS

In an injection molding process, it's essential to avoid mold damage, prevent breakage and prolong the mold's life. Therefore, the Automatic Ramp Calibration feature as part of the KePlast Software provides a solution: it will look for the optimal moment to open and close the mold in an injection molding process.

Mold damages can be a significant concern for plastics manufacturers as they can lead to production delays, scrap or rework of defective parts, and increased maintenance costs.

Furthermore, calibrating a machine after a mold exchange can be a very long and expert-demanding process, machine type independent, because calculating and testing manually requires lots of time and expertise, including many trial-error situations – something the plant’s owners want to avoid for sure in times of qualified workforce shortages.

One alternative for automatically identifying how quickly the mold should close and open at these different stages is the Automatic Ramp Calibration feature commonly available as a part of KePlast Software.


EXTEND THE MOLD LIFESPAN AND SPEED UP THE MOLD EXCHANGE PROCESS
KEBA engineer testing the function on actual machines in the IMM lab in Linz

Man vs. machine
A short analogy of this function to daily life is car parking. When thinking of the last curve one needs to take to get to the final parking position, the driver decides at what velocity and with which acceleration the car should move to achieve the smoothest possible movement.

Stepping on the gas and directing the steering wheel in a specific direction to reach the final position too fast leads to problems with immediate need of braking, resulting in pressure overload on brakes, and may move the car slightly forward because of shaking. However, we also do not want to park the car too slowly because there are simply better things to do.

We, humans, learn from our experiences and are able to adapt the parking velocity to protect our vehicles. The same applies to open and close movements of injection molding machines, it is, however, not so straightforward to imagine.

Impact of multi-stage mold profile movements on the mold lifespan
The injection molding process's open and close movements usually have two to five velocity stages for mold close and three to five for mold open, each requiring the molds to move at different velocities and with different acceleration or deceleration to avoid unnecessary mold damage caused by excessive braking and shaking.

Velocity gives the idea of the mold’s speed but also tells the direction in which it is moving, and on KePlast screen view, the horizontal lines show constant velocity, and the steep lines show the change in velocity. Acceleration refers to a change of velocity in time – being that a speed up or slow down. And as a ramp, we consider the linear change of velocity, which can be adjusted with “Start %”, “Mid %” and “Stop” parameters.

Molds under control - also without active brake control
The changes in velocity and acceleration are usually executed through a manually-configurated active brake control mechanism. It changes the brake valve or servo valve position, the cross-section where oil flows through, after (and before) the cylinder that moves the mold. So, depending on the desired case, the cross-section is either smaller, resulting in higher resistance to the flow of oil and stronger braking effect, or the cross-section is larger, meaning reduced resistance and lower braking effect.

Since the prices for active brake controls are pretty high, not all machines are equipped with them. If there is no active brake control mechanism, therefore, without the valve, the cross-section is either completely open or closed, not usable for active braking. The mold is then only broken by friction or due to the toggle lever. Thus, soon enough, too much oil must stop being pumped.

The good news is that the Auto Calibration feature works perfectly in both cases and is a preferred option for standard or low-end machines without active brake control.

At the right time, at the right place
Let’s look closer at what actually happens with an injection molding machine when we want a mold to stop at a particular spot at a specific time. The graphic below shows the desired velocity of the open movement (black curves) and the actual measured values of the vector (blue curves). When focusing on the braking, the last and crucial phase of the opening process, we can clearly see the negative velocity followed by a positive one – which is a sign of machine shaking.


EXTEND THE MOLD LIFESPAN AND SPEED UP THE MOLD EXCHANGE PROCESS
A typical mold open stop ramp evaluation

Now, the machine's options to avoid extensive shaking are to use an active brake control mechanism with the help of a brake valve or a more expensive servo valve for which the process experts need to find the correct values and set them up in the control system manually – or use the algorithm calculated and tested values from the KePlast Automatic Ramp Calibration feature.

A PLC from KEBA with KePlast Software has a precise, intelligent auto-calibrating function, which answers the question of how much shaking shall be allowed and adapts the processes accordingly.

By evaluating the optimizing criterium, which is, in this case, the oscillation, defined as the shaking at the end of the movement, the robust algorithm identifies the “trade-off “ ramp values with the help of numerous auto-calibration movements like the idle, reference & validation ones.

KePlast Automatic Ramp Calibration - 3 steps:
  • Algorithm evaluates the oscillation at the end of the movement (A)
  • It then uses the oscillation of a slow movement as a reference (A)
  • Then performs numerous auto-calibration movements to identify the most suitable value based on the optimal “Max (B) & Stop (C)” values

EXTEND THE MOLD LIFESPAN AND SPEED UP THE MOLD EXCHANGE PROCESS
Mold open auto-calibration – the overview of all steps the algorithm executes

As a result, the algorithm finds the highest possible Max and Stop ramp values highest acceptable oscillation.

Summary: the benefits of KePlast Automatic Ramp Calibration feature
  • Smooth movements & smooth braking for longer mold life
  • No or fewer experts needed as well as saved time by the mold exchange process
  • Set the max-braking capacity quickly and easily without adverse effects on the machine
  • For any hydraulic machine type, also suitable for braking with servo valve
This article is part of KEBA's whitepaper "Faster & more accurate control technology with KEBA concepts & KePlast Smart Functions". If you found this article insightful, we invite you to download the complete whitepaper for the comprehensive narrative.

www.keba.com

  Ask For More Information…

LinkedIn
Pinterest

Join the 155,000+ IMP followers